| ID |
Date |
Author |
Type |
Category |
Subject |
Text |
 |
|
93
|
07 Nov 2019 02:34 |
Sam | Routine | General | Run 966 Laser Run with SiPMs at 65V, 30us trace | Laser Intensity: MIN
Threshold: external
clock (laser NIM), laser set to 1kHz |
|
|
14
|
19 Feb 2019 16:26 |
Pierre-A. | Configuration | General | Overall HW configuration | For Reference,
I put a simple schematic for the
Trigger/Run control. |
|
|
9
|
31 Jan 2019 15:18 |
Pierre | Configuration | Trigger | Trigger rate | Somehow the trigger rate was not matching
the trigger source.
Find out that Link 3 was not collecting and |
|
|
10
|
06 Feb 2019 14:12 |
Pierre | Configuration | Hardware | Extended Trigger Time Tag (ETTT) | Confirmed this ETTT configuration is working.
ETTT Enabled [22..21] |
|
|
13
|
13 Feb 2019 16:45 |
Pierre | Problem | Hardware | A3818 from Marco | Checking again Marco's A3818:
- Port #2 (third from top of card) is acting
up.
|
|
|
22
|
27 Mar 2019 08:57 |
Pierre | Configuration | Hardware | CERN setup | Found that the Trigger out from the CB is
on output1
Trigger / Not used
|
|
|
23
|
27 Mar 2019 14:04 |
Pierre | Configuration | Trigger | Time stamp sync | The ChronoBox latest FW is loaded. Let tme
know if this is what the chronobox should
look like in term of registers.
|
|
|
24
|
28 Mar 2019 02:18 |
Pierre | Configuration | Trigger | Test | |
|
|
140
|
18 Nov 2019 02:40 |
Pascal/Julie | Routine | General | Laser run | Run 1232 Laser run
Chronobox: External
trigger Enable |
|
|
144
|
19 Nov 2019 00:14 |
Pascal/Julie | Routine | General | Laser run | Run 1252 Laser run
Chronobox: External
trigger Enable |
|
|
32
|
12 Jul 2019 01:27 |
Marco Rescigno | Configuration | | MB1 test in proto-0 setup/1 | Changed custom size to 500 (20 us), tested
ok run 681 |
|
|
33
|
12 Jul 2019 02:05 |
Marco Rescigno | Problem | Trigger | MB1 test in proto-0 setup/1 | Tried to get laser sync signal into chronobox
(clkin1 input), apparently all triggers dropped
by chronobox |
|
|
34
|
12 Jul 2019 06:01 |
Marco Rescigno | Routine | General | Run 703 | Run 703 is being writte on disk.
16 channels of board 00.
Laser trigger at 10 Hz |
|
|
35
|
12 Jul 2019 07:58 |
Marco Rescigno | Routine | General | MB1 test in proto-0 setup/day 2 | Implemented a simple charge integration
on the midas display, most of the channels
look almost as good as this one. |
|
|
36
|
12 Jul 2019 11:34 |
Marco Rescigno | Routine | General | MB1 test in proto-0 setup/2 Run 718 | Run 718 has 25 channel readout Board 0
ch 0-15 and Board 0 ch 0-7.
Laser triggered, some noise, maybe |
|
|
37
|
13 Jul 2019 14:50 |
Marco Rescigno | Routine | General | Long Laser run on disk | Run 747 , 250 k events
as requested by alessandro 40%
post trigger, acquisition window 16 us. |
|
|
38
|
16 Jul 2019 01:58 |
Marco Rescigno | Routine | General | Run 766 (Laser) | Laser Run with Vbias=65 V , new recommended
value from PE group
500 k events acquired |
|
|
39
|
16 Jul 2019 02:39 |
Marco Rescigno | Routine | General | run 771, scintillation events triggering on ch11 and ch12 of board0 | Trigger setup with a threshold of 1500
ADC count wrt to baseline, on just two channels.
This is also to limit the trigger |
|
|
40
|
16 Jul 2019 02:41 |
Marco Rescigno | Problem | Trigger | Busy handling | This morning tried to get some data with
Vbias=65 V, which seems better for the SiPM
in MB1. |
|
|
41
|
16 Jul 2019 03:17 |
Marco Rescigno | Routine | General | run 772, scintillation events triggering on all channels | Majority of 5, threshold at 1000 ADC count,
13 channels enabled (10 trigger signals)
50 Hz, 30 us window. |
|