| ID |
Date |
Author |
Type |
Category |
Subject |
Text |
 |
|
131
|
14 Nov 2019 04:03 |
Yi/Edgar/Sam | Routine | General | Noise data taking | Run 1121
Gas pocket: OFF
Fields: |
|
|
130
|
14 Nov 2019 03:51 |
E. Sanchez | Routine | General | S1 data taking without field | Run 1133
Gas pocket: OFF
Fields: OFF |
|
|
129
|
14 Nov 2019 00:33 |
E. Sanchez | Routine | General | Morning data taking | It is not possible to access to the Chronobox
page
Run 1109 Laser run |
|
|
128
|
14 Nov 2019 00:09 |
Ben Smith | Problem | Hardware | Chronobox not serving human webpage | The chronobox isn't serving the human-interactive
webpage that should be visible at https://m-darkside.web.cern.ch/chronobox/
- it responds with "File not found". Oddly, |
|
|
127
|
13 Nov 2019 09:24 |
Xiang Xiao | Routine | General | Evening data taking | Run 1105
Gas pocket: ON
(thinkness 7mm) |
|
|
126
|
13 Nov 2019 08:15 |
Ben Smith | Routine | Software | Don't worry about "Param Not Found Type" error messages | When we start the HV program (CAEN_SY4527),
it spews error messages of the form:
"16:58:30.035 2019/11/13 [CAEN_SY4527,ERROR] |
|
|
125
|
13 Nov 2019 00:08 |
Yi Wang | Routine | General | Morning data taking | Run 1099
Gas pocket: ON
(thinkness 7mm) |
|
|
124
|
12 Nov 2019 10:08 |
Edgar Sanchez | Routine | General | Laser run | Run 1096 Laser run
Chronobox: External
trigger Enable |
|
|
123
|
12 Nov 2019 09:30 |
Edgar Sanchez | Routine | General | Afternoon system monitoring | Run 1092
Gas pocket: ON
(thinkness 7mm) |
|
|
122
|
12 Nov 2019 09:22 |
Edgar Sanchez | Routine | General | Afternoon system monitoring | Run 1090
Gas pocket: ON
(thinkness 7mm) |
|
|
121
|
12 Nov 2019 00:24 |
Yi Wang | Routine | General | Morning data taking | Run 1084
Gas pocket: ON
(thinkness 7mm) |
|
|
120
|
12 Nov 2019 00:23 |
Ben Smith | Problem | Digitizer | V1725 error, runs keep crashing | It looks like there's a memory leak in the
high voltage driver, and we were running
out of memory (using a lot of swap). That |
|
|
119
|
12 Nov 2019 00:16 |
Yi Wang | Problem | Digitizer | V1725 error, runs keep crashing | 09:15:33.955 2019/11/12 [feov1725MTI00,ERROR]
[feoV1725.cxx:663:link_thread,ERROR] Exiting
thread 3 with error |
|
|
118
|
11 Nov 2019 23:57 |
Yi Wang | Problem Fixed | Trigger | ID 117 problem is fixed | The problem reported in ID 117 is somehow
fixed this morning. |
|
|
117
|
11 Nov 2019 10:05 |
Sam Hill | Problem | General | Evening data taking | Attemted the following run, and
it started but the rate was shoing 0 and
it got stuck on 5 events |
|
|
116
|
11 Nov 2019 09:31 |
Sam Hill | Routine | General | Afternoon system monitoring: IV curves and Dewar refill | 17:30
Took a set of IV curves using 0.5V
steps from 30-50V and 0.05 steps above 50V. |
|
|
115
|
11 Nov 2019 01:12 |
Yi / Edgar | Routine | General | Morning data taking | Run 1065
Gas pocket: ON
(thinkness 7mm) |
|
|
114
|
11 Nov 2019 00:47 |
Yi / Edgar | Problem Fixed | Digitizer | Problem fixed by restarting the VME crate | |
|
|
113
|
11 Nov 2019 00:37 |
Yi Wang | Problem | MIDAS | cannot connect to rootana | The connection to rootana is lost.
No data taking can be started. |
|
|
112
|
10 Nov 2019 12:15 |
E. Sanchez | Problem | MIDAS | Problem DAQ | Error during data taking 1573416708
21:11:48.151 2019/11/10 [feov1725MTI00,INFO]
V1725 PLL loss lock Board:0 (vmeAcq=0x0) |
|