/* * - DaVinci Audio Serial Port support */ #ifndef __ASM_HARDWARE_MCASP_H #define __ASM_HARDWARE_MCASP_H #include #include /* Bases of dm644x and dm355 register banks */ #define DAVINCI_ASP0_BASE 0x01E02000 #define DAVINCI_ASP1_BASE 0x01E04000 /* Bases of dm365 register banks */ #define DAVINCI_DM365_ASP0_BASE 0x01D02000 /* Bases of dm646x register banks */ #define DAVINCI_DM646X_MCASP0_REG_BASE 0x01D01000 #define DAVINCI_DM646X_MCASP1_REG_BASE 0x01D01800 /* Bases of da850/da830 McASP0 register banks */ #define DAVINCI_DA8XX_MCASP0_REG_BASE 0x01D00000 /* Bases of da830 McASP1 register banks */ #define DAVINCI_DA830_MCASP1_REG_BASE 0x01D04000 /* EDMA channels of dm644x and dm355 */ #define DAVINCI_DMA_ASP0_TX 2 #define DAVINCI_DMA_ASP0_RX 3 #define DAVINCI_DMA_ASP1_TX 8 #define DAVINCI_DMA_ASP1_RX 9 /* EDMA channels of dm646x */ #define DAVINCI_DM646X_DMA_MCASP0_AXEVT0 6 #define DAVINCI_DM646X_DMA_MCASP0_AREVT0 9 #define DAVINCI_DM646X_DMA_MCASP1_AXEVT1 12 /* EDMA channels of da850/da830 McASP0 */ #define DAVINCI_DA8XX_DMA_MCASP0_AREVT 0 #define DAVINCI_DA8XX_DMA_MCASP0_AXEVT 1 /* EDMA channels of da830 McASP1 */ #define DAVINCI_DA830_DMA_MCASP1_AREVT 2 #define DAVINCI_DA830_DMA_MCASP1_AXEVT 3 /* Interrupts */ #define DAVINCI_ASP0_RX_INT IRQ_MBRINT #define DAVINCI_ASP0_TX_INT IRQ_MBXINT #define DAVINCI_ASP1_RX_INT IRQ_MBRINT #define DAVINCI_ASP1_TX_INT IRQ_MBXINT struct snd_platform_data { u32 tx_dma_offset; u32 rx_dma_offset; enum dma_event_q asp_chan_q; /* event queue number for ASP channel */ enum dma_event_q ram_chan_q; /* event queue number for RAM channel */ unsigned int codec_fmt; /* * Allowing this is more efficient and eliminates left and right swaps * caused by underruns, but will swap the left and right channels * when compared to previous behavior. */ unsigned enable_channel_combine:1; unsigned sram_size_playback; unsigned sram_size_capture; /* * If McBSP peripheral gets the clock from an external pin, * there are three chooses, that are MCBSP_CLKX, MCBSP_CLKR * and MCBSP_CLKS. * Depending on different hardware connections it is possible * to use this setting to change the behaviour of McBSP * driver. The dm365_clk_input_pin enum is available for dm365 */ int clk_input_pin; /* * This flag works when both clock and FS are outputs for the cpu * and makes clock more accurate (FS is not symmetrical and the * clock is very fast. * The clock becoming faster is named * i2s continuous serial clock (I2S_SCK) and it is an externally * visible bit clock. * * first line : WordSelect * second line : ContinuousSerialClock * third line: SerialData * * SYMMETRICAL APPROACH: * _______________________ LEFT * _| RIGHT |______________________| * _ _ _ _ _ _ _ _ * _| |_| |_ x16 _| |_| |_| |_| |_ x16 _| |_| |_ * _ _ _ _ _ _ _ _ * _/ \_/ \_ ... _/ \_/ \_/ \_/ \_ ... _/ \_/ \_ * \_/ \_/ \_/ \_/ \_/ \_/ \_/ \_/ * * ACCURATE CLOCK APPROACH: * ______________ LEFT * _| RIGHT |_______________________________| * _ _ _ _ _ _ _ _ _ * _| |_ x16 _| |_| |_ x16 _| |_| |_| |_| |_| |_| | * _ _ _ _ dummy cycles * _/ \_ ... _/ \_/ \_ ... _/ \__________________ * \_/ \_/ \_/ \_/ * */ bool i2s_accurate_sck; /* McASP specific fields */ int tdm_slots; u8 op_mode; u8 num_serializer; u8 *serial_dir; u8 version; u8 txnumevt; u8 rxnumevt; int (*get_context_loss_count)(struct device *); }; enum { MCASP_VERSION_1 = 0, /* DM646x */ MCASP_VERSION_2, /* DA8xx/OMAPL1x */ MCASP_VERSION_3, /* AM33xx */ }; enum dm365_clk_input_pin { MCBSP_CLKR = 0, /* DM365 */ MCBSP_CLKS, }; #define INACTIVE_MODE 0 #define TX_MODE 1 #define RX_MODE 2 #define DAVINCI_MCASP_IIS_MODE 0 #define DAVINCI_MCASP_DIT_MODE 1 #if (defined(CONFIG_SOC_OMAPAM33XX) && (defined(CONFIG_SND_AM33XX_SOC) \ || (defined(CONFIG_SND_AM33XX_SOC_MODULE)))) #define davinci_gen_pool omap_gen_pool #endif #endif /* __ASM_HARDWARE_MCASP_H */